Spool of 10 m (394").

Stretchability: at least 200 %.

No ageing after 6 weeks maximum stretching.

Art. no. 35312  (Maximum resistance 200 g)

For supporting the weak muscles of the fingers.

Art. no. 35313  (Maximum resistance 400 g)

For most dynamic finger splints.

Art. no. 35314  (Maximum resistance 600 g)

For dynamic wrist extension splints or for very persistent finger contractures.

Instructions for use (IFU)

The Single Orfitube Adjuster puts you in full control of longitudinal and lateral position of Orfitubes. But there is more than one angle from which you can look at this product. The compact design allows you to fix one individual adjuster for each finger. The adjusters are lightweight, very cost-effective and more elegant than ever before.

Art. no. : 35305

Instruction for use (IFU)

For easy bending of the strong Orfitubes without stress on the thumbs.

Art. no. : 35308

Instructions for use (IFU)

Chromium-plated tube ends, fit on all Orfitubes, reducing rubbing of the elastic thread with the tube edge to a minimum.

Art. no. : 35318  (20 pieces)

Instructions for use (IFU)

Contains:

- 10 tubes of 330 mm (13") long.

- 3 different types of elastic thread with different degrees of elastic strength (on a spool).

- 1 spool polyester monofilament for an optimal gliding effect (if necessary)

- 2 bending wires.

Art. no. : 35311

Instruction for use (IFU)

10 tubes of 330 mm (13") long, incl. 2 bending wires.

Art. no. : 35310

Instructions for use (IFU)

Spool of 75 m (2953").

Used to increase the gliding of the elastic thread in the Orfitube, e.g. when the Orfitube is locally kinked and when the length of the elastic is not determined.

Art. no. : 35315

Instructions for use (IFU)

Art. no.: 35304  (5 pieces)

Instructions for use (IFU)

Stainless steel spring. The short leg is secured between two layers of Orfit Classic. The long leg is bent to size. At total finger flexion the spring is tightened up to a torque force of ca. 2000 g.cm. The spring is especially designed for finer extension assists in combination with the Orfit Splint.

Gauge 1 mm (1/24") - coil diameter 4 mm (1/6").

Art. no. : 35802  (10 pieces)

Instructions for use (IFU)

Stainless steel spring. The short leg is bent and anchored in the dorsal bridge of the splint. The long leg is bent and cut to length. The spring power is adjusted by altering the coil design.

Gauge 0.7 mm (1/37") - coil diameter 5 mm (1/5").

Art. no. : 35800  (10 pieces)

Instructions for use (IFU)

Stainless steel spring. Designed to assist the intrinsic muscle weakness, e.g. with ulnar nerve palsy. The spring can also be turned upside down to increase the spring power. Torque at full finger extension: ca. 1000 g.cm.

Art. no. : 35801  (10 pieces)

Instructions for use (IFU)

Radial nerve patients need two strong assisting extension coils. When recovering, the coils help to rebalance muscle power.

Kit:

- 2 Orfit precuts 3.2 mm (1/8") non perfo stiff

- 2 lateral coil springs: gauge diameter 1.5 mm (1/16")

  Coil diameter 15 mm (3/5") - Torque force: 5000 g.cm

Art. no. : 35865K (Small) - 35866K (Medium) - 35867K (Large)

Instructions for use (IFU)

For making your own coil springs and outriggers.

Length : 15 m (591")

Thickness : 1 mm (1/24")

Art. no. : 35805

Instructions for use (IFU)

Stainless steel spring. Two types supplied: coiled left or right. Torque force when tightened over an angle of 130° : 5000 g.cm.

Gauge 1.5 mm (1/16") - coil diameter 15 mm (3/5").

Art. no. : 35804  (10 pieces : 5 left + 5 right)

Instructions for use (IFU)