The History of the Check Socket

The World’s First Prosthesis. Credit: Jacqueline Finch of the University of Manchester

The field of prosthetics has a long and rich history. Did you know it dates back to Ancient Egypt? The oldest practical prosthesis known to man is a toe made of wood and leather, which archaeologists found attached to the 3000-year old remains of an Egyptian noblewoman (950-710 B.C.).

And one fascinating aspect of this history is that of the check socket in particular. Let’s go over some fun facts of its first applications and the materials that were typically used.

 

Prosthetic socket materials throughout history

Nowadays, prosthetic sockets are made of innovative plastic and silicone materials, but this has not always been the case.

The first transfemoral sockets consisted of wood and leather and had a conical shape on the inside. The basic conical socket later advanced into a quadrilateral socket. This type could comfortably bear the amputee’s weight on the ischial-gluteal area of the residual limb and came with an air valve and an air space at the bottom. Many patients had good results with these sockets, but many also suffered from edema and skin problems.

Later on, prosthetists introduced wooden sockets that had full contact with the stump. This new shape decreased the problems with edema and helped to keep the prosthesis in place.

Wood and leather were the materials of preference for a long time. And while they enabled prosthetists to make good prosthetic sockets, they were not ideal. Wood is difficult and time-consuming to shape and it changes with the humidity levels of the environment; leather is a challenge to keep clean. Thus, prosthetists started experimenting with plastics and resins, which made the prosthetic fabrication process more efficient. Moreover, they allowed prosthetists to check the fit of the socket.

 

The first check sockets

Check socket fitting

Socket fitting. Credit: O&P Virtual Library

Check sockets as we know them today, did not begin being used until the 1950s. Before that, prosthetists did not yet consider them a useful step in the creation of the perfect prosthesis.

One of the reasons for their relatively late application was the controversy that surrounded check sockets. At the time, many prosthetists looked down upon the notion of a check socket. They believed it to be a redundant step in the creation of a prothesis. Their thoughts are, if the perfect techniques were used from the beginning, than the prosthetic socket would fit perfectly and therefore, the sockets would not need adjustments.

New socket materials

In the 1950s and 1960s, this attitude changed. With the introduction of new transparent socket materials, prosthetists did start to see the value of using a test socket. The clear sockets allowed prosthetists to immediately see the areas that needed adjustment in the definitive socket, such as areas of redness or areas with lack of contact.

The first clear check sockets consisted of Plexiglas. However, as this material was so tedious and time-consuming to shape, researchers started to look for alternatives. They tried making sockets from acrylic and polyester resins, but these were equally difficult to work with and quite pricey. They soon got replaced with plastic laminates and thermoplastics, which were less expensive and easier to form.

Historical picture showing the vacuum-forming of a check socket.

Vacuum-forming a check socket. Credit: O&P Virtual Library

Introduction of vacuum-forming

A highlight in the search for a more practical solution came in 1972, when Mooney and Snelson introduced a new socket fabrication method.

The researchers showed how to create check sockets by vacuum-forming a polycarbonate sheet material over a positive mold of the patient’s residual limb. It was a ground-breaking method at the time which made it very easy to fabricate clear check sockets on a professional basis. The method is still in use today and works with several other types of thermoplastics.

Today, transparent check sockets are widely accepted and used. They are a valuable step in the creation of a definitive socket that is as comfortable as it is practical.

Orfit’s thermoplastic check socket material, Orfitrans Stiff, can be molded by vacuum-forming (bubble-forming/blister-forming).

 

References

Bennett Wilson Jr., A. (1992). History of Amputation Surgery and Prosthetics. In J. Bowker, & J. Michael (Eds.), Atlas of Limb Prosthetics: Surgical, Prosthetic, and Rehabilitation Principles (2nd ed.). Retrieved from http://www.oandplibrary.org/alp/chap01-01.asp

Hamontree, S., & Snelson, R. (1973). The Use Of Check Sockets In Lower-Limb Prosthetics. Orthotics and Prosthetics27(4), 30–33. Retrieved from http://www.oandplibrary.org/op/1973_04_030.asp

Mooney, V., & Snelson, R. (1972). Fabrication and Application of Transparent Polycarbonate Sockets. Orthotics and Prosthetics26(1), 1–13. Retrieved from http://www.oandplibrary.org/op/1972_01_001.asp

Perry Clements, I. (n.d.). How Prosthetic Limbs Work – The History of Prosthetic Limbs. Retrieved December 5, 2018, from https://science.howstuffworks.com/prosthetic-limb1.htm

Quigley, M. (1985). The Role of Test Socket Procedures in Today’s Prosthetic Practices. Clinical Prosthetics & Orthotics9(3), 11–12. Retrieved from http://www.oandplibrary.org/cpo/1985_03_011.asp

 

Contact us for more product information or find your local distributor here.

 

If you’d like to receive the latest product updates and interesting Orfit news, subscribe to our newsletter:

We've selected some similar articles for you
Advantages of Using a Thermoplastic Check Socket
Using a test socket to obtain the perfect fit
A check socket is an essential aid in the creation of a qualitative definitive socket that will last the patient many years. Taking the extra time to fit the patient with a check socket before fabricating their actual definitive socket truly pays off in the long term and offers both the patient and the prosthetist many advantages.
Read more
A Step-by-Step Guide to Moulding a Flexible Prosthetic Socket
Pull the perfect prosthetic sockets
In this guide, we explain how to expertly mould our flexible thermoplastic sheets for perfectly smooth and soft sockets. We share how to prepare the sheet, optimize your positive mould and some moulding tips so that you can make the most out of these advanced prosthetic socket materials. 
Read more
The Drape Forming Method for Prosthetic Sockets
How to drape form with Orfitrans Excel
The drape forming method is a tried and tested method for the fabrication of (inner) prosthetic sockets and orthoses. Discover our best drape forming tips and tricks and learn how to get optimal fabrication results from Orfitrans Excel.
Read more